Skip to main content Skip to search Skip to main navigation
Application
  • Thread: BSF 1/4″ × 26 threads/inch – British Whitworth fine thread to BS 84
  • Design: 2-piece hand tap set to DIN 2181
  • Tool material: HSS-G – ground high-speed steel for readily machinable materials up to 900 N/mm², particularly unalloyed and low-alloy steels
  • Hole types: Through holes and blind holes
  • Recommended tap drill diameter: 5.2 mm

With the Hand tap 2-piece set DIN 2181 HSS-G - BSF 1/4 x 26 you can cut BSF internal threads precisely by hand. The two-piece set consists of a taper tap and bottoming tap, used in sequence. The matching thread combination is BSF 1/4″ with 26 threads per inch. Identical nominal inch sizes in other thread systems are not automatically compatible.

Two cutting stages provide a clear working sequence for manual tapping. The profile is produced gradually, with the cutting work shared between the taper tap and bottoming tap. This allows more controlled application of force and loading of each tool than cutting the entire thread in one operation. The set is therefore also suitable for machining locations with limited machine access.

The tap set is intended for manually producing BSF 1/4″ × 26 threads/inch in through holes and blind holes. Typical tasks include BSF threaded holes in angle brackets, fastening components and mounting plates, particularly in readily machinable unalloyed and low-alloy steels up to 900 N/mm². Applications include workshop use, metalworking, assembly and maintenance.

Materials and specific applications

Specific applications

Typical tasks include BSF threaded holes in angle brackets, fastening components and mounting plates. The component drawing must specify the thread designation BSF 1/4″ × 26 threads/inch; check the material against the suitability information below.

Existing threads can be recut if their size, pitch and condition allow it. This does not restore missing material or severely damaged threads.

Suitable materials

  • readily machinable materials up to 900 N/mm²
  • unalloyed and low-alloy steels

Dimensions

Technical dimensional drawing of the hand tap showing nominal diameter, shank diameter D2, overall length L1 and thread length L2
Cutting diameter D 6.35 mm
Shank diameter D2 6 mm
Overall length L1 50 mm
Thread length L2 18 mm
Square drive 4.9 mm

Tool design

  • Standard: DIN 2181
  • Tool material: HSS-G – ground high-speed steel
  • Product type: Hand tap set
  • Design: 2-piece set
  • Thread type: British Whitworth fine thread
  • Thread standard: BS 84
  • Thread size: BSF 1/4″ × 26 threads/inch
  • Thread tolerance: medium
  • Thread direction: Right-hand thread
  • Flute form: N (straight flutes)
  • Thread pitch: 26 threads/inch

Chamfer of the two cutting stages

No. 1 – Taper tap5–6-thread chamfer
No. 2 – Bottoming tap2–3-thread chamfer

The chamfer is the front cutting section in which the thread profile is built up gradually.

Cutting threads – step by step

  1. Secure the workpiece
    Clamp the workpiece securely so that it cannot rotate. The hole must be readily accessible so that the tap can be started squarely and guided in line with the hole axis throughout the operation.
  2. Prepare the tapping drill hole
    Drill the tapping drill hole for BSF 1/4″ × 26 threads/inch to the recommended diameter of 5.2 mm. You can find a clear overview of selection and calculation in the VÖLKEL article Calculating the tapping drill hole size for taps.
  3. Deburr and clean the hole
    Remove the burr at the hole entrance and clear away loose drilling chips. A clean, lightly chamfered hole makes it easier to start the taper tap squarely and prevents damage to the first thread.
  4. Tapping with the taper tap
    Clamp the taper tap in a suitable tool holder and align it precisely with the hole axis. Apply sufficient cutting lubricant for tapping to the tool and hole. Turn the taper tap into the workpiece with steady pressure.
  5. Tapping with the bottoming tap
    Finally, insert the bottoming tap and apply sufficient cutting lubricant again. The bottoming tap produces the complete internal thread profile. Work with steady movements and avoid excessive force, particularly when the bottoming tap reaches the bottom of a blind hole.
  6. Check the thread
    Remove chips and residual cutting lubricant from the finished thread. Then check the thread size and ease of engagement using a suitable inspection tool, such as a GO/NO-GO thread plug gauge if compliance with the required tolerance must be demonstrated.

Further guidance is available in the VÖLKEL blog article Cutting clean threads: how to produce internal and external threads .

Scope of delivery

  • Hand Tap Rougher DIN 2181 HSS-G - BSF 1/4 x 26 (22714-1)
  • Hand Tap Finisher DIN 2181 HSS-G - BSF 1/4 x 26 (22714-3)

Frequently asked questions (FAQ)

What specifications must a mating component meet for BSF 1/4 inch?

It must match the BSF specification with a 1/4 inch nominal size and 26 threads per inch. Another 1/4 inch thread is not automatically compatible.

Which tapping drill do I need for BSF 1/4″ × 26 threads/inch?

For BSF 1/4″ × 26 threads/inch, the recommended tap drill diameter is 5.2 mm. Guidance on preparing the tapping drill hole. The simplified metric tapping drill hole formula is not applied indiscriminately to this thread designation.

Are a 1/4 inch thread and a 1/4 inch holder fitting the same selection size?

No. The thread size determines the internal thread to be cut. Select the tap wrench according to the tool's square drive and the appropriate clamping range.

How do I identify and inspect a BSF 1/4″ × 26 threads/inch internal thread?

First measure the outside diameter of the matching bolt or mating component with a caliper and determine the pitch or threads per inch with a thread pitch gauge. Compare the values, thread profile and standard with the designation BSF 1/4″ × 26 threads/inch. For an unknown internal thread, identification using a matching external thread or a thread gauge is safer than forcing in a trial fastener. Inspect the finished internal thread dimensionally with a suitable limit thread plug gauge.

What is the nominal diameter of BSF 1/4 inch in mm?

The converted nominal diameter is 6.35 mm. Do not therefore automatically predrill to 6.35 mm: the separate recommended value applies to the tapping drill hole.

What thread tolerance applies to item 22714?

The specified thread tolerance is medium. This designation is retained as “medium” and is not converted into a metric ISO tolerance class without supporting evidence. If necessary, check compliance with the required thread tolerance using a suitable GO/NO-GO thread plug gauge.

Why should I check the final digit when replacing an individual tap?

The taper tap in this set is designated 22714-1 and the bottoming tap 22714-3. The bottoming tap retains the suffix -3 even though the set contains only two tools.

Which individual tools can I reorder for item 22714?

The set includes taper tap 22714-1, bottoming tap 22714-3. When reordering, also compare the standard, thread and tool material.

Technical documentation: Hand taps – technical information (PDF) · VD 23 catalogue (PDF, German/English)

Further technical knowledge: Hand taps in the VÖLKEL tap glossary.

Do you need help with selection or use?
Use the VÖLKEL contact form .

Additional information
Type of thread British Standard Fine Thread
Standard DIN 2181
Material HSS-G
Tolerance medium
Size BSF 1/4 x 26
Overall length (L1) 50 mm
Thread length (L2) 18 mm
Core hole diameter (D1) 5.2 mm
Shank diameter (D2) 6.0 mm
Drive connector 4.9 mm
EAN 4022835227144
Item number 22714
Type of flute straight fluted
Application for through and blind holes
Thread standard BS 84