Hand Tap set of 2 pieces DIN 2181 HSS-G - BSF 1" x 10
€51.80
- Thread: BSF 1″ × 10 threads/inch – British Whitworth fine thread to BS 84
- Design: 2-piece hand tap set to DIN 2181
- Tool material: HSS-G – ground high-speed steel for readily machinable materials up to 900 N/mm², particularly unalloyed and low-alloy steels
- Hole types: Through holes and blind holes
- Recommended tap drill diameter: 22.5 mm
With the Hand tap 2-piece set DIN 2181 HSS-G - BSF 1" x 10 you can cut BSF internal threads precisely by hand. The two-piece set consists of a taper tap and bottoming tap, used in sequence. BSF 1″ has 10 threads per inch here. This combination must match the existing mating thread; a BSW thread of the same nominal size is no substitute.
The two matched cutting stages share the work between initial tapping and finish tapping. The profile is produced in controlled, successive steps, allowing the load per tool and the force required to be reduced compared with cutting in one operation. Manual operation provides direct feedback on the progress of the cut. It is also usable where machine access is limited.
The tap set is intended for manually producing BSF 1″ × 10 threads/inch in through holes and blind holes. Typical tasks include fastening threads in components with an existing BSF specification, particularly in readily machinable unalloyed and low-alloy steels up to 900 N/mm². Applications include workshop use, metalworking, assembly and maintenance.
Materials and specific applications
Specific applications
The set is suitable for producing and recutting BSF 1″ × 10 internal threads on replacement and repair parts for British machinery, equipment and classic vehicles, provided that the drawing, original part or mating component specifies this exact thread. Typical components include solid housings, bearing blocks, brackets, flanges and clamping or fastening elements with a corresponding large imperial screw connection.
During maintenance, dirty, corroded or slightly deformed thread turns can be recut. Torn-out flanks, missing material or an incorrect thread profile cannot be restored with the tap.
Suitable materials
- readily machinable materials up to 900 N/mm²
- unalloyed and low-alloy steels
Dimensions
| Cutting diameter D | 25.4 mm |
|---|---|
| Shank diameter D2 | 18 mm |
| Overall length L1 | 110 mm |
| Thread length L2 | 40 mm |
| Square drive | 14.5 mm |
Tool design
- Standard: DIN 2181
- Tool material: HSS-G – ground high-speed steel
- Product type: Hand tap set
- Design: 2-piece set
- Thread type: British Whitworth fine thread
- Thread standard: BS 84
- Thread size: BSF 1″ × 10 threads/inch
- Thread tolerance: medium
- Thread direction: Right-hand thread
- Flute form: N (straight flutes)
- Thread pitch: 10 threads/inch
Chamfer of the two cutting stages
| No. 1 – Taper tap | 5–6-thread chamfer |
|---|---|
| No. 2 – Bottoming tap | 2–3-thread chamfer |
The chamfer is the front cutting section in which the thread profile is built up gradually.
Cutting threads – step by step
-
Secure the workpiece
Clamp the workpiece securely so that it cannot rotate. The hole must be readily accessible so that the tap can be started squarely and guided in line with the hole axis throughout the operation. - Prepare the tapping drill hole
Drill the tapping drill hole for BSF 1″ × 10 threads/inch to the recommended diameter of 22.5 mm. You can find a clear overview of selection and calculation in the VÖLKEL article Calculating the tapping drill hole size for taps. -
Deburr and clean the hole
Remove the burr at the hole entrance and clear away loose drilling chips. A clean, lightly chamfered hole makes it easier to start the taper tap squarely and prevents damage to the first thread. -
Tapping with the taper tap
Clamp the taper tap in a suitable tool holder and align it precisely with the hole axis. Apply sufficient cutting lubricant for tapping to the tool and hole. Turn the taper tap into the workpiece with steady pressure. -
Tapping with the bottoming tap
Finally, insert the bottoming tap and apply sufficient cutting lubricant again. The bottoming tap produces the complete internal thread profile. Work with steady movements and avoid excessive force, particularly when the bottoming tap reaches the bottom of a blind hole. -
Check the thread
Remove chips and residual cutting lubricant from the finished thread. Then check the thread size and ease of engagement using a suitable inspection tool, such as a GO/NO-GO thread plug gauge if compliance with the required tolerance must be demonstrated.
Further guidance is available in the VÖLKEL blog article Cutting clean threads: how to produce internal and external threads .
Scope of delivery
Frequently asked questions (FAQ)
- How do I know whether I need BSF 1 inch with 10 threads per inch?
First measure the outside diameter of the matching bolt or mating component with a caliper; for BSF 1″ it is close to the nominal diameter of 25.4 mm. Then apply a thread pitch gauge and check whether the 10 TPI blade fits cleanly across several thread turns. The 55° Whitworth profile must also match. For an unknown internal thread, identification using the matching external thread, a BSF thread table or a thread gauge is safer than forcing in a trial fastener.
- Which tapping drill do I need for BSF 1″ × 10 threads/inch?
For BSF 1″ × 10 threads/inch, the recommended tap drill diameter is 22.5 mm. The simplified metric tap drill formula is not applied indiscriminately to this thread designation.
- Can I use the set for a BSW 1 inch thread?
No. The BSW 1 inch set also selected cuts 8 threads per inch. This BSF set, however, is intended for 10 threads per inch; the two threads are not interchangeable.
- What is the correct sequence for the 2-piece set?
Taper tap followed by bottoming tap. The matched cutting stages build up the profile gradually. The bottoming tap produces the complete internal thread. Tapping step by step.
- Which diameter is shown for BSF 1 inch in the technical drawing?
The technical drawing specifies cutting diameter D as 25.4 mm. This is not the tap drill diameter; the separately specified value of 22.5 mm applies to predrilling.
- How do I inspect the finished BSF 1″ × 10 internal thread?
Use a suitable BSF 1″ × 10 limit thread plug gauge for dimensional inspection. The GO side must screw in over the specified inspection length in accordance with the applicable inspection rule; the NO-GO side may engage only to the permitted extent. A bolt or mating component can check function, but it does not replace standards-compliant limit gauging.
- Why does the bottoming tap in this two-piece set end in -3?
The individual item number is 22738-3. It is an item identifier and does not state how many tools the set contains. The set includes taper tap 22738-1 and bottoming tap 22738-3.
- Which individual tools can I reorder for item 22738?
The set includes taper tap 22738-1, bottoming tap 22738-3. When reordering, also compare the standard, thread and tool material.
Technical documentation: Hand taps – technical information (PDF) · VD 23 catalogue (PDF, German/English)
Further technical knowledge: Hand taps in the VÖLKEL tap glossary.
Do you need help with selection or use?
Use the VÖLKEL contact form
.
| Type of thread | British Standard Fine Thread |
|---|---|
| Standard | DIN 2181 |
| Material | HSS-G |
| Tolerance | medium |
| Size | BSF 1" x 10 |
| Overall length (L1) | 110 mm |
| Thread length (L2) | 40 mm |
| Core hole diameter (D1) | 22.5 mm |
| Shank diameter (D2) | 18.0 mm |
| Drive connector | 14.5 mm |
| EAN | 4022835227380 |
| Item number | 22738 |
| Type of flute | straight fluted |
| Application | for through and blind holes |
| Thread standard | BS 84 |