Skip to main content Skip to search Skip to main navigation
Application
  • Thread: BSF 7/8″ × 11 threads/inch – British Whitworth fine thread to BS 84
  • Design: 2-piece hand tap set to DIN 2181
  • Tool material: HSS-G – ground high-speed steel for readily machinable materials up to 900 N/mm², particularly unalloyed and low-alloy steels
  • Hole types: Through holes and blind holes
  • Recommended tap drill diameter: 19.5 mm

With the Hand tap 2-piece set DIN 2181 HSS-G - BSF 7/8 x 11 you can cut BSF internal threads precisely by hand. The two-piece set consists of a taper tap and bottoming tap, used in sequence. The thread specification combines BSF 7/8″ with 11 threads per inch. Switching to another 7/8 inch system also requires a different tool.

The matched two-piece set allows a controlled process through to the finished internal thread. The tools share the cutting work, distributing the force required over several operations. This can reduce the load per tool compared with cutting the complete thread in one operation. Manual operation is also possible at installation locations with difficult access, provided guidance in line with the hole axis is ensured.

The tap set is intended for manually producing BSF 7/8″ × 11 threads/inch in through holes and blind holes. Typical tasks include 7/8 inch BSF threads in supporting and connecting components according to the drawing, particularly in readily machinable unalloyed and low-alloy steels up to 900 N/mm². Applications include workshop use, metalworking, assembly and maintenance.

Materials and specific applications

Specific applications

Typical tasks include 7/8 inch BSF threads in supporting and connecting components according to the drawing. The component drawing must specify the thread designation BSF 7/8″ × 11 threads/inch; check the material against the suitability information below.

Existing threads can be recut if their size, pitch and condition allow it. This does not restore missing material or severely damaged threads.

Suitable materials

  • readily machinable materials up to 900 N/mm²
  • unalloyed and low-alloy steels

Dimensions

Technical dimensional drawing of the hand tap showing nominal diameter, shank diameter D2, overall length L1 and thread length L2
Cutting diameter D 22.225 mm
Shank diameter D2 18 mm
Overall length L1 100 mm
Thread length L2 36 mm
Square drive 14.5 mm

Tool design

  • Standard: DIN 2181
  • Tool material: HSS-G – ground high-speed steel
  • Product type: Hand tap set
  • Design: 2-piece set
  • Thread type: British Whitworth fine thread
  • Thread standard: BS 84
  • Thread size: BSF 7/8″ × 11 threads/inch
  • Thread tolerance: medium
  • Thread direction: Right-hand thread
  • Flute form: N (straight flutes)
  • Thread pitch: 11 threads/inch

Chamfer of the two cutting stages

No. 1 – Taper tap5–6-thread chamfer
No. 2 – Bottoming tap2–3-thread chamfer

The chamfer is the front cutting section in which the thread profile is built up gradually.

Cutting threads – step by step

  1. Secure the workpiece
    Clamp the workpiece securely so that it cannot rotate. The hole must be readily accessible so that the tap can be started squarely and guided in line with the hole axis throughout the operation.
  2. Prepare the tapping drill hole
    Drill the tapping drill hole for BSF 7/8″ × 11 threads/inch to the recommended diameter of 19.5 mm. You can find a clear overview of selection and calculation in the VÖLKEL article Calculating the tapping drill hole size for taps.
  3. Deburr and clean the hole
    Remove the burr at the hole entrance and clear away loose drilling chips. A clean, lightly chamfered hole makes it easier to start the taper tap squarely and prevents damage to the first thread.
  4. Tapping with the taper tap
    Clamp the taper tap in a suitable tool holder and align it precisely with the hole axis. Apply sufficient cutting lubricant for tapping to the tool and hole. Turn the taper tap into the workpiece with steady pressure.
  5. Tapping with the bottoming tap
    Finally, insert the bottoming tap and apply sufficient cutting lubricant again. The bottoming tap produces the complete internal thread profile. Work with steady movements and avoid excessive force, particularly when the bottoming tap reaches the bottom of a blind hole.
  6. Check the thread
    Remove chips and residual cutting lubricant from the finished thread. Then check the thread size and ease of engagement using a suitable inspection tool, such as a GO/NO-GO thread plug gauge if compliance with the required tolerance must be demonstrated.

Further guidance is available in the VÖLKEL blog article Cutting clean threads: how to produce internal and external threads .

Scope of delivery

  • Hand Tap Rougher DIN 2181 HSS-G - BSF 7/8 x 11 (22734-1)
  • Hand Tap Finisher DIN 2181 HSS-G - BSF 7/8 x 11 (22734-3)

Frequently asked questions (FAQ)

How does BSF 7/8 inch differ from another 7/8 inch system?

This item is matched to the BSF specification with 11 threads per inch. Other inch systems may differ in profile and pitch. The same nominal size does not mean interchangeability.

Which tapping drill do I need for BSF 7/8″ × 11 threads/inch?

For BSF 7/8″ × 11 threads/inch, the recommended tap drill diameter is 19.5 mm. Guidance on preparing the tapping drill hole. The simplified metric tapping drill hole formula is not applied indiscriminately to this thread designation.

What does bottoming tap 22734-3 do?

It is used after taper tap 22734-1 and produces the complete internal thread. It is listed as No. 2 in the table for the two-piece set.

What is the correct sequence for the 2-piece set?

Taper tap followed by bottoming tap. The matched cutting stages build up the profile gradually. The bottoming tap produces the complete internal thread. Tapping step by step.

Can I use the set for a left-hand BSF-7/8 thread?

No. The selected version cuts right-hand threads. A left-hand thread requires a tool designed for that purpose; the same size and thread count are insufficient.

How do I identify and inspect a BSF 7/8″ × 11 threads/inch internal thread?

First measure the outside diameter of the matching bolt or mating component with a caliper and determine the pitch or threads per inch with a thread pitch gauge. Compare the values, thread profile and standard with the designation BSF 7/8″ × 11 threads/inch. For an unknown internal thread, identification using a matching external thread or a thread gauge is safer than forcing in a trial fastener. Inspect the finished internal thread dimensionally with a suitable limit thread plug gauge.

What must I plan for blind holes in addition to the tap drill diameter?

The drilled depth must provide space for the chamfer and chips beyond the required usable thread depth. This also applies to the bottoming tap with its short chamfer. Avoid contact with the bottom of the hole.

Which individual tools can I reorder for item 22734?

The set includes taper tap 22734-1, bottoming tap 22734-3. When reordering, also compare the standard, thread and tool material.

Technical documentation: Hand taps – technical information (PDF) · VD 23 catalogue (PDF, German/English)

Further technical knowledge: Hand taps in the VÖLKEL tap glossary.

Do you need help with selection or use?
Use the VÖLKEL contact form .

Additional information
Type of thread British Standard Fine Thread
Standard DIN 2181
Material HSS-G
Tolerance medium
Size BSF 7/8 x 11
Overall length (L1) 100 mm
Thread length (L2) 36 mm
Core hole diameter (D1) 19.5 mm
Shank diameter (D2) 18.0 mm
Drive connector 14.5 mm
EAN 4022835227342
Item number 22734
Type of flute straight fluted
Application for through and blind holes
Thread standard BS 84