Skip to main content Skip to search Skip to main navigation
Application
  • Thread: G 1″ × 11 threads/inch – parallel Whitworth pipe thread (BSPP) to DIN ISO 228
  • Design: 2-piece hand tap set to DIN 5157
  • Tool material: HSS-G – ground high-speed steel for readily machinable materials up to 900 N/mm², particularly unalloyed and low-alloy steels
  • Hole types: Through holes and blind holes
  • Recommended tap drill diameter: 30.75 mm

With the Hand tap 2-piece set DIN 5157 HSS-G - G (BSP) 1" x 11 you can cut parallel G pipe threads precisely by hand. The two-piece set consists of a taper tap and bottoming tap, used in sequence. The G pipe thread is defined by its nominal size and 11 threads per inch. The designation G 1 does not represent an actual thread diameter of 25.4 mm.

The two-stage process separates starting the thread from finishing the profile. Matched cutting stages share the cutting work and help reduce tool loading. Steady manual guidance allows good control of the tapping process. As a manual tool holder is sufficient, the set can also be used where machine access is limited.

The tap set is intended for manually producing G 1″ × 11 threads/inch in through holes and blind holes. Typical tasks include G-1 connection threads in housings and connecting components according to the drawing, particularly in readily machinable unalloyed and low-alloy steels up to 900 N/mm². Applications include workshop use, metalworking, assembly and maintenance. The leak tightness of a pipe connection depends on the intended connection design and is not ensured by cutting the G thread alone.

Materials and specific applications

Specific applications

Typical tasks include G-1 connection threads in housings and connecting components according to the drawing. The component drawing must specify the thread designation G 1″ × 11 threads/inch; check the material against the suitability information below.

One application example is internal threads in matching G-1 connecting and adapter components for water and irrigation connections. The mating component must be explicitly intended for G 1. Leak tightness is achieved by the designed connection with its appropriate seal, rather than by the cut G thread alone.

Existing threads can be recut if their size, pitch and condition allow it. This does not restore missing material or severely damaged threads.

Suitable materials

  • readily machinable materials up to 900 N/mm²
  • unalloyed and low-alloy steels

Dimensions

Technical dimensional drawing of the hand tap showing nominal diameter, shank diameter D2, overall length L1 and thread length L2
Cutting diameter D 33.249 mm
Shank diameter D2 25 mm
Overall length L1 100 mm
Thread length L2 25 mm
Square drive 20 mm

Tool design

  • Standard: DIN 5157
  • Tool material: HSS-G – ground high-speed steel
  • Product type: Hand tap set
  • Design: 2-piece set
  • Thread type: Parallel Whitworth pipe thread (BSPP)
  • Thread standard: DIN ISO 228
  • Thread size: G 1″ × 11 threads/inch
  • Thread tolerance: medium
  • Thread direction: Right-hand thread
  • Flute form: N (straight flutes)
  • Thread pitch: 11 threads/inch

Chamfer of the two cutting stages

No. 1 – Taper tap5–6-thread chamfer
No. 2 – Bottoming tap2–3-thread chamfer

The chamfer is the front cutting section in which the thread profile is built up gradually.

Cutting threads – step by step

  1. Secure the workpiece
    Clamp the workpiece securely so that it cannot rotate. The hole must be readily accessible so that the tap can be started squarely and guided in line with the hole axis throughout the operation.
  2. Prepare the tapping drill hole
    Drill the tapping drill hole for G 1″ × 11 threads/inch to the recommended diameter of 30.75 mm. You can find a clear overview of selection and calculation in the VÖLKEL article Calculating the tapping drill hole size for taps.
  3. Deburr and clean the hole
    Remove the burr at the hole entrance and clear away loose drilling chips. A clean, lightly chamfered hole makes it easier to start the taper tap squarely and prevents damage to the first thread.
  4. Tapping with the taper tap
    Clamp the taper tap in a suitable tool holder and align it precisely with the hole axis. Apply sufficient cutting lubricant for tapping to the tool and hole. Turn the taper tap into the workpiece with steady pressure.
  5. Tapping with the bottoming tap
    Finally, insert the bottoming tap and apply sufficient cutting lubricant again. The bottoming tap produces the complete internal thread profile. Work with steady movements and avoid excessive force, particularly when the bottoming tap reaches the bottom of a blind hole.
  6. Check the thread
    Remove chips and residual cutting lubricant from the finished thread. Then check the thread size and ease of engagement using a suitable inspection tool, such as a GO/NO-GO thread plug gauge if compliance with the required tolerance must be demonstrated.

Further guidance is available in the VÖLKEL blog article Cutting clean threads: how to produce internal and external threads .

Scope of delivery

  • Hand Tap Rougher DIN 5157 HSS-G - G (BSP) 1" x 11 (25326-1)
  • Hand Tap Finisher DIN 5157 HSS-G - G (BSP) 1" x 11 (25326-2)

Frequently asked questions (FAQ)

Why does G 1 have 33.249 mm in the dimension table instead of 25.4 mm?

G 1 is the nominal size of a pipe thread. It does not directly correspond to an outside diameter of one inch. For this parallel G thread, the thread outside diameter is 33.249 mm.

Which tapping drill do I need for G 1″ × 11 threads/inch?

For G 1″ × 11 threads/inch, the recommended tap drill diameter is 30.75 mm. Guidance on preparing the tapping drill hole. The simplified metric tapping drill hole formula is not applied indiscriminately to this thread designation.

Is a cut G-1 thread already leak-tight without further measures?

The G thread alone does not produce a pressure-tight connection. The intended connection design and its seal must suit the application.

What is the correct sequence for the 2-piece set?

Taper tap followed by bottoming tap. The matched cutting stages build up the profile gradually. The bottoming tap produces the complete internal thread. Tapping step by step.

Can I produce a tapered R or Rc thread with it?

No. This set is intended for the parallel G-1 internal thread. For tapered pipe threads, select a tool with the appropriate thread designation.

How do I identify and inspect a G 1″ × 11 threads/inch internal thread?

First measure the outside diameter of the matching bolt or mating component with a caliper and determine the pitch or threads per inch with a thread pitch gauge. Compare the values, thread profile and standard with the designation G 1″ × 11 threads/inch. For an unknown internal thread, identification using a matching external thread or a thread gauge is safer than forcing in a trial fastener. Inspect the finished internal thread dimensionally with a suitable limit thread plug gauge.

How does item 25326 differ from HSS-E set 55326?

Both selected sets are intended for G 1 with 11 threads per inch. Item 25326 is made from HSS-G and item 55326 from HSS-E. The material suitability must therefore be checked in addition to the identical thread size.

Which individual tools can I reorder for item 25326?

The set includes taper tap 25326-1, bottoming tap 25326-2. When reordering, also compare the standard, thread and tool material.

Technical documentation: Hand taps – technical information (PDF) · VD 23 catalogue (PDF, German/English)

Further technical knowledge: Hand taps in the VÖLKEL tap glossary.

Do you need help with selection or use?
Use the VÖLKEL contact form .

Additional information
Type of thread Pipe thread
Standard DIN 5157
Material HSS-G
Tolerance medium
Size G (BSP) 1" x 11
Overall length (L1) 100 mm
Thread length (L2) 25 mm
Core hole diameter (D1) 30.75 mm
Shank diameter (D2) 25.0 mm
Drive connector 20.0 mm
EAN 4022835253266
Item number 25326
Type of flute straight fluted
Application for through and blind holes
Thread standard DIN ISO 228