Skip to main content Skip to search Skip to main navigation

What is an inch thread? And why 1 inch is not always 25.4 mm

The connection is marked “1 inch”, but the caliper reads just over 33 mm. A measuring error? No. You are looking at a pipe thread, and here the inch designation describes the pipe, not the thread.

An inch thread is a thread whose dimensions are based on the inch (1 inch = 25.4 mm). The size appears as an inch fraction or a number in the designation, while the pitch is stated as the number of threads per inch. However, the term covers two different worlds: American and British threads. They differ in flank angle, thread count and in what the inch designation actually means.

The essentials in 30 seconds

  • Two families: American threads (UNC, UNF, UNEF, NPT) have a 60° flank angle; British Whitworth threads (BSW, BSF, G, R) have 55°.
  • Pitch: It is specified in threads per inch. Divide 25.4 by the thread count to obtain the pitch in millimetres.
  • Inch designation: For fastening threads, it is the outside diameter; for pipe threads, it is only a nominal size. A G 1 measures just over 33 mm.
  • Same number, different thread: The same nominal size or the same thread count does not mean that two threads fit together.
Simon Siebert, Head of Production and Quality Assurance at VÖLKEL

Users are most often surprised by pipe threads: why does a 1-inch thread have an outside diameter of just over 33 mm rather than 25.4 mm? With a pipe thread, the inch designation is a name, not a dimension. The rule is therefore: identify the thread system first, then measure and check the table.

Simon Siebert, Head of Production & Quality Assurance

American or British: which inch threads are there?

Almost every inch thread belongs to one of two families.

When the term Unified is used—that is, UNC, UNF or UNEF—it refers to the American system. Unified threads have a 60° flank angle and are standardised in ASME B1.1. The American tapered NPT pipe thread also uses 60°.

British threads are based on the Whitworth profile. It has rounded crests and roots and a flank angle of 55°. This family includes the BSW and BSF fastening threads and the G, R, Rp and Rc pipe threads.

You can hardly see the five-degree difference with the naked eye. It is nevertheless decisive for mating the threads, as the misconceptions further below show.

AbbreviationFamilyFlank angleStandardClassification
UNCAmerican (Unified)60°ASME B1.1Coarse thread
UNFAmerican (Unified)60°ASME B1.1Fine thread
UNEFAmerican (Unified)60°ASME B1.1Extra-fine thread
NPTAmerican60°ASME B1.20.1Tapered pipe thread, seals in the thread
BSWBritish (Whitworth)55°BS 84Coarse thread
BSFBritish (Whitworth)55°BS 84Fine thread
G (BSPP)British (Whitworth)55°ISO 228-1Parallel pipe thread, does not seal in the thread
R, Rp, Rc (BSPT)British (Whitworth)55°ISO 7-1, EN 10226Pipe thread that seals in the thread (R and Rc tapered, Rp parallel)

You can read about the practical differences between UNC and UNF and when a fine thread is worthwhile in our article Fine thread or coarse thread: what is the difference?

Whitworth pipe threads are now governed by ISO and EN standards. Their profile nevertheless originates from the British system, which is why they are grouped under the term BSP (British Standard Pipe). BSP is therefore not one single thread: it includes the parallel G thread and the thread-sealing R, Rp and Rc variants. If you only read “BSP”, you do not yet know whether the thread is parallel or tapered. Our article Pipe thread types explained: G threads, R threads and NPT shows how to distinguish G, R, Rp, Rc and NPT reliably.

You will encounter UNC and UNF mainly on machines, vehicles and components from North America, and BSW and BSF on older British equipment. Whitworth pipe threads, by contrast, are also part of everyday life in Europe, from water connections to compressed air. Two examples from our blog are the BSF 3/8 x 20 fishing thread and the G 5/8 thread on diving equipment.

Why are there two inch systems?

In 1841, Joseph Whitworth proposed a thread in England with rounded thread forms and a 55° flank angle, which became the British standard. In 1864, William Sellers countered in the USA with a 60° thread featuring flattened crests and roots. This created two inch systems that looked similar but still did not fit together.

Following interchangeability problems during the Second World War, Great Britain, the USA and Canada agreed on a common Unified thread in November 1948. It was based on the American profile and adopted its 60° angle.

Whitworth did not disappear as a result. BSW and BSF can be found on many British cars up to the 1950s, which keeps them relevant for classic-car mechanics to this day. In pipe threads, the British profile even prevailed: BSP with 55° is widespread around the world, except in North America. This is why water connections in Europe use a Whitworth profile, while connections from North America generally use NPT.

What does the inch designation mean on a thread?

For fastening threads, whether American or British, the inch designation states the nominal diameter—that is, the outside diameter of the thread. 1/4 inch equals 6.35 mm, 3/8 inch 9.525 mm and 1/2 inch 12.7 mm.

Below 1/4 inch, the two systems take different approaches. Only the American Unified system changes from fractions to numbers here, from No. 0 to No. 12. The diameter can be calculated: 0.060 inch plus 0.013 inch for each number, which gives 0.190 inch for No. 10. That is 4.826 mm.

British threads, by contrast, continue to use inch fractions; number sizes do not exist in that system. BSW extends down to 1/16 inch, while BSF begins at 3/16 inch.

American (Unified)British (Whitworth)
Sizes below 1/4 inchNumbers from No. 0 to No. 12Fractions: 1/16, 3/32, 1/8, 5/32, 3/16, 7/32
Smallest sizeNo. 0 x 80 UNF, 1.524 mmBSW 1/16 x 60, 1.588 mm
Example around 4.8 mmNo. 10-24 UNC, 4.826 mmBSW 3/16 x 24, 4.763 mm
From 1/4 inchInch fractionsInch fractions

No. 0 corresponds to 0.060 inch or 1.524 mm and is available only with 80 threads. BSW 1/16 has an outside diameter of 1.588 mm with 60 threads, while BSW 3/16 has 4.763 mm with 24 threads.

Pipe threads also start at 1/16 inch. However, a G 1/16 has an outside diameter of 7.723 mm because the number is a nominal size in this case. More on this further below.

The nominal dimension is also not the dimension you read on the caliper. Due to tolerances, an external thread is always slightly smaller. For a 1/2-13 UNC screw in tolerance class 2A, the dimension is approximately 12.39 to 12.66 mm instead of 12.7 mm.

How is the pitch of inch threads specified?

A metric thread states the pitch directly: on an M10 x 1.5 thread, the thread turns are 1.5 mm apart. Inch threads instead count how many thread turns occur over one inch of thread length. The international abbreviation for this is TPI (threads per inch).

You obtain the pitch in millimetres by dividing 25.4 by the thread count. A 1/2-13 UNC has 13 threads per inch and therefore a pitch of 1.954 mm; a 1/2-20 UNF has 1.270 mm. Unlike a metric thread, a larger number therefore means a finer thread.

In many catalogues, the thread count appears after an “x”, including in ours: UNC 1/2 x 13 or G (BSP) 1/2 x 14. This looks like a metric fine-thread designation, but it means something different. The 13 and 14 are threads per inch, not millimetres.

Why does a 1-inch pipe thread not have an outside diameter of 25.4 mm?

Because the nominal size of a pipe thread describes the pipe, not the thread. Originally, the dimensions referred to the inside diameter. The thread is located on the outside of the pipe and is correspondingly larger. A G 1 has an outside diameter of 33.249 mm with 11 threads per inch.

A comparison of all 1-inch threads shows how far apart the systems are at the same nominal size:

ThreadFamilyFlank angleThreads per inchPitchOutside Ø (nominal dimension)Tapping drill Ø according to VÖLKEL table
UNC 1 x 8American60°83.175 mm25.400 mm22.25 mm
UNF 1 x 12American60°122.117 mm25.400 mm23.25 mm
UNEF 1 x 20American60°201.270 mm25.400 mm24.25 mm
BSW 1 x 8British55°83.175 mm25.400 mm22.0 mm
BSF 1 x 10British55°102.540 mm25.400 mm22.5 mm
G 1 x 11British55°112.309 mm33.249 mm30.75 mm
NPT 1 x 11.5American60°11.52.209 mm33.401 mm (pipe outside Ø)29.0 mm

At 1 inch, the Unified series have 8, 12 and 20 threads, BSW has 8 and BSF 10 threads. For NPT 1, the table specifies a pipe outside diameter of 33.401 mm with 11.5 threads. The recommended tapping drill holes from our table range from 22 mm for BSW to 30.75 mm for G 1.

Seven threads carry the same nominal size, and five of them even share the same outside diameter. Nevertheless, none of them fit together.

The typical mistake is to measure the outside diameter and divide it by 25.4. With a G 1, this gives approximately 1.31 inches, or about 1 5/16, and you look for the wrong tool.

With NPT, there is the additional factor that the thread is tapered. The taper is 1:16, and the tabulated value is the pipe outside diameter. The measured value therefore depends on where you measure.

How do you read a complete inch-thread designation?

A complete designation states the size, thread count and thread system, often supplemented by tolerance and direction of rotation.

1/4-20 UNC-2A (American): 1/4-inch nominal diameter (6.35 mm), 20 threads per inch, Unified coarse thread. 2A is the tolerance class. The number denotes class 1 to 3, A denotes an external thread and B an internal thread. This is why our UNC hand taps are marked with tolerance 2B.

No. 10-32 UNF (American): Number size 10 (4.826 mm), 32 threads per inch, Unified fine thread.

BSW 1/2 x 12 (British): Whitworth coarse thread with a 1/2-inch nominal diameter and 12 threads per inch. Because the thread count for BSW is fixed for each diameter, you will also find the short form W 1/2.

G 1/2 A (British profile): Parallel pipe thread to ISO 228-1 in nominal size 1/2. The letter A or B indicates the tolerance class of the external thread; the internal thread is simply designated G 1/2.

R 1/2, Rp 1/2, Rc 1/2 (British profile): Tapered external thread, parallel internal thread and tapered internal thread for connections that seal in the thread.

1/2-14 NPT (American): Tapered pipe thread, nominal size 1/2, 14 threads per inch.

Left-hand threads receive the suffix LH after the designation.

Four misconceptions about inch threads

“Same thread count, same thread.” This is precisely where it becomes tricky. UNC 1 x 8 and BSW 1 x 8 have the same thread count and nominal diameter, as do the almost identical No. 10-24 UNC and BSW 3/16 x 24. G 1/2 and NPT 1/2 each have 14 threads. The difference lies in the flank angle: 60° versus 55°. The threads can be screwed together for a short distance, but the flanks do not contact cleanly, and the connection does not carry loads or seal as designed. Our article NPT or BSPT: what is the difference? explains how to distinguish NPT and BSPT in the workshop.

“BSP is always parallel.” BSP is the umbrella term for Whitworth pipe threads. G is parallel, R and Rc are tapered, and Rp is a parallel internal thread for tapered external threads. Only the identifying letter tells you what is meant.

“An inch screw is almost metric.” A 5/16-18 UNC has an outside diameter of 7.94 mm and a pitch of 1.411 mm; M8 has 8 mm and 1.25 mm. An M8 nut can be started, but it jams after a few turns. Continuing to turn it damages both threads.

“Sealing tape makes every pipe thread leak-tight.” The G thread is designed for connections that do not seal in the thread. A flat gasket or O-ring provides the seal. Treating a G thread as self-sealing without an additional seal almost always causes a leak. The R/Rp and R/Rc pairings, as well as NPT, do seal in the thread.

You can reliably distinguish the systems in three steps: measure the outside diameter, determine the thread count with a 55° and 60° thread gauge, and compare both values with the table. A thread gauge provides final certainty. You can find suitable thread gauges for inch threads here.

Workshop cheat sheet: converting inch threads to millimetres

Pitch in mm = 25.4 ÷ threads per inch

Nominal diameter in mm = inch fraction × 25.4 (fastening threads only)

Unified number size in mm = (0.060 + 0.013 × number) × 25.4

Pipe threads: do not calculate; look them up in the table

Download the cheat sheet as a PDF
Threads per inchPitchTypical examples
83.175 mmUNC 1, BSW 1
112.309 mmG 1, UNC 5/8, BSW 5/8
11.52.209 mmNPT 1
122.117 mmBSW 1/2, UNF 1
131.954 mmUNC 1/2
141.814 mmG 1/2, NPT 1/2, UNC 7/16, BSW 7/16
161.588 mmUNC 3/8, BSW 3/8, BSF 1/2
181.411 mmUNC 5/16, NPT 1/4
191.337 mmG 1/4, G 3/8
201.270 mmUNC 1/4, BSW 1/4, UNF 1/2
241.058 mmUNC No. 10, BSW 3/16, UNF 3/8
280.907 mmUNF 1/4, G 1/8, UNEF 1/2

How do you find the correct tapping drill size for an inch thread?

The rule of thumb “nominal diameter minus pitch” comes from the metric system. For inch threads, it is better to use table values because the nominal size and the actual diameter are not always directly related. Our tapping drill calculator contains 19 thread systems with 581 sizes, including UNC, UNF and pipe threads.

Application advice for VÖLKEL threading tools
Application consulting
Always the perfect product for your application
Request consulting