Skip to main content Skip to search Skip to main navigation
Application
  • Thread: BSF 3/4″ × 12 threads/inch – British Whitworth fine thread to BS 84
  • Design: 2-piece hand tap set to DIN 2181
  • Tool material: HSS-G – ground high-speed steel for readily machinable materials up to 900 N/mm², particularly unalloyed and low-alloy steels
  • Hole types: Through holes and blind holes
  • Recommended tap drill diameter: 16.5 mm

With the Hand tap 2-piece set DIN 2181 HSS-G - BSF 3/4 x 12 you can cut BSF internal threads precisely by hand. The two-piece set consists of a taper tap and bottoming tap, used in sequence. The set produces the combination BSF 3/4″ with 12 threads per inch. Before reworking an existing thread, both its profile and thread count must be known.

In the two-stage thread-cutting sequence, each tool performs a matched operation. This division supports manageable cutting resistance and can reduce individual tool loading. Manual feed allows accurate starting and controlled further guidance. No machine is required for use on components with difficult access.

The tap set is intended for manually producing BSF 3/4″ × 12 threads/inch in through holes and blind holes. Typical tasks include 3/4 inch BSF threads in brackets and components in workshop and maintenance work, particularly in readily machinable unalloyed and low-alloy steels up to 900 N/mm². Applications include workshop use, metalworking, assembly and maintenance.

Materials and specific applications

Specific applications

Typical tasks include 3/4 inch BSF threads in brackets and components in workshop and maintenance work. The component drawing must specify the thread designation BSF 3/4″ × 12 threads/inch; check the material against the suitability information below.

Existing threads can be recut if their size, pitch and condition allow it. This does not restore missing material or severely damaged threads.

Suitable materials

  • readily machinable materials up to 900 N/mm²
  • unalloyed and low-alloy steels

Dimensions

Technical dimensional drawing of the hand tap showing nominal diameter, shank diameter D2, overall length L1 and thread length L2
Cutting diameter D 19.05 mm
Shank diameter D2 14 mm
Overall length L1 95 mm
Thread length L2 32 mm
Square drive 11 mm

Tool design

  • Standard: DIN 2181
  • Tool material: HSS-G – ground high-speed steel
  • Product type: Hand tap set
  • Design: 2-piece set
  • Thread type: British Whitworth fine thread
  • Thread standard: BS 84
  • Thread size: BSF 3/4″ × 12 threads/inch
  • Thread tolerance: medium
  • Thread direction: Right-hand thread
  • Flute form: N (straight flutes)
  • Thread pitch: 12 threads/inch

Chamfer of the two cutting stages

No. 1 – Taper tap5–6-thread chamfer
No. 2 – Bottoming tap2–3-thread chamfer

The chamfer is the front cutting section in which the thread profile is built up gradually.

Cutting threads – step by step

  1. Secure the workpiece
    Clamp the workpiece securely so that it cannot rotate. The hole must be readily accessible so that the tap can be started squarely and guided in line with the hole axis throughout the operation.
  2. Prepare the tapping drill hole
    Drill the tapping drill hole for BSF 3/4″ × 12 threads/inch to the recommended diameter of 16.5 mm. You can find a clear overview of selection and calculation in the VÖLKEL article Calculating the tapping drill hole size for taps.
  3. Deburr and clean the hole
    Remove the burr at the hole entrance and clear away loose drilling chips. A clean, lightly chamfered hole makes it easier to start the taper tap squarely and prevents damage to the first thread.
  4. Tapping with the taper tap
    Clamp the taper tap in a suitable tool holder and align it precisely with the hole axis. Apply sufficient cutting lubricant for tapping to the tool and hole. Turn the taper tap into the workpiece with steady pressure.
  5. Tapping with the bottoming tap
    Finally, insert the bottoming tap and apply sufficient cutting lubricant again. The bottoming tap produces the complete internal thread profile. Work with steady movements and avoid excessive force, particularly when the bottoming tap reaches the bottom of a blind hole.
  6. Check the thread
    Remove chips and residual cutting lubricant from the finished thread. Then check the thread size and ease of engagement using a suitable inspection tool, such as a GO/NO-GO thread plug gauge if compliance with the required tolerance must be demonstrated.

Further guidance is available in the VÖLKEL blog article Cutting clean threads: how to produce internal and external threads .

Scope of delivery

  • Hand Tap Rougher DIN 2181 HSS-G - BSF 3/4 x 12 (22730-1)
  • Hand Tap Finisher DIN 2181 HSS-G - BSF 3/4 x 12 (22730-3)

Frequently asked questions (FAQ)

What must match when reworking BSF 3/4 inch?

The thread system, nominal size, 12 threads per inch and thread direction must match the existing hole. Also check its condition: recutting cannot replace missing material.

Which tapping drill do I need for BSF 3/4″ × 12 threads/inch?

For BSF 3/4″ × 12 threads/inch, the recommended tap drill diameter is 16.5 mm. Guidance on preparing the tapping drill hole. The simplified metric tapping drill hole formula is not applied indiscriminately to this thread designation.

Is 3/4 inch a pipe thread size in this set?

No. The item is designated as a BSF fastening thread with 12 threads per inch. A G-3/4 pipe thread belongs to a different system and must not be treated as equivalent.

How do I identify and inspect a BSF 3/4″ × 12 threads/inch internal thread?

First measure the outside diameter of the matching bolt or mating component with a caliper and determine the pitch or threads per inch with a thread pitch gauge. Compare the values, thread profile and standard with the designation BSF 3/4″ × 12 threads/inch. For an unknown internal thread, identification using a matching external thread or a thread gauge is safer than forcing in a trial fastener. Inspect the finished internal thread dimensionally with a suitable limit thread plug gauge.

Why does the drawing state 19.05 mm?

This is the nominal diameter of BSF 3/4 inch converted to millimetres. The conversion changes neither the pitch nor the thread system.

Which tap wrench fits this hand tap?

The holder must securely grip the 11 mm square drive. Compare this value with the specified clamping range of the tap wrench or tool holder. Choosing the right tap wrench.

What chamfers do the two tools in the BSF-3/4 set have?
The taper tap, item 22730-1, has a 5–6-thread chamfer. The bottoming tap, item 22730-3, has a 2–3-thread chamfer. Use the tools in this order.
Can I recut existing BSF 3/4″ × 12 threads/inch threads?

After checking the condition of the thread, reworking is possible if thread type, size, pitch and direction match. Missing material or severely damaged threads cannot be restored by recutting.

Technical documentation: Hand taps – technical information (PDF) · VD 23 catalogue (PDF, German/English)

Further technical knowledge: Hand taps in the VÖLKEL tap glossary.

Do you need help with selection or use?
Use the VÖLKEL contact form .

Additional information
Type of thread British Standard Fine Thread
Standard DIN 2181
Material HSS-G
Tolerance medium
Size BSF 3/4 x 12
Overall length (L1) 95 mm
Thread length (L2) 32 mm
Core hole diameter (D1) 16.5 mm
Shank diameter (D2) 14.0 mm
Drive connector 11.0 mm
EAN 4022835227304
Item number 22730
Type of flute straight fluted
Application for through and blind holes
Thread standard BS 84