Hand Tap set of 3 pieces DIN 352 HSSE - M 10 x 1.5
€26.40
- Thread: M10 × 1.5 – metric ISO coarse thread to DIN 13
- Design: 3-piece hand tap set to DIN 352
- Tool material: HSS-E – high-speed steel with high edge retention for difficult-to-machine materials, steels up to 1,200 N/mm² and general use
- Hole types: Through holes and blind holes
- Recommended tap drill diameter: 8.5 mm
With the Hand tap 3-piece set DIN 352 HSSE - M 10 x 1.5 you can cut metric coarse threads precisely by hand. The three-piece set consists of a taper tap (1 ring), second tap (2 rings) and bottoming tap (no ring), used in sequence. The combination M10 × 1.5 denotes the metric coarse thread. A different set is required for an M10 fine thread with a different pitch.
The three-stage working sequence distributes profile production across three tools. This divides the cutting force and tool loading compared with cutting the entire thread in one operation. The user guides the tap wrench in a controlled manner and immediately feels changes in resistance. Manual tapping remains possible without machine access if sufficient space is available for the tool and holder.
The tap set is intended for manually producing M10 × 1.5 in through holes and blind holes. Typical tasks include M10 fastening threads in mounting plates, brackets and machine components, particularly in difficult-to-machine materials and steels up to 1,200 N/mm²; the HSS-E version is also intended for general use. Applications include workshop use, metalworking, assembly and maintenance.
Materials and specific applications
Specific applications
Typical tasks include M10 fastening threads in mounting plates, brackets and machine components. The component drawing must specify the thread designation M10 × 1.5; check the material against the suitability information below.
One specific motorcycle application is internal threads in matching mirror mounts and mirror adapters whose drawing explicitly specifies M10 × 1.5 as a right-hand thread. This version occurs on certain motorcycle mirror connections. Before production or reworking, the thread pitch, direction and required engagement length must match the particular mirror connection. The set is intended neither for M10 × 1.25 nor for a left-hand mirror thread.
Existing threads can be recut if their size, pitch and condition allow it. This does not restore missing material or severely damaged threads.
Suitable materials
- high cutting-edge durability
- difficult-to-machine materials
- steels up to 1,200 N/mm²
- also suitable for general use
Dimensions
| Cutting diameter D | 10 mm |
|---|---|
| Shank diameter D2 | 7 mm |
| Overall length L1 | 70 mm |
| Thread length L2 | 24 mm |
| Square drive | 5.5 mm |
Tool design
- Standard: DIN 352
- Tool material: HSS-E – high-speed steel with high edge retention
- Product type: Hand tap set
- Design: 3-piece set
- Thread type: Metric ISO coarse thread
- Thread standard: DIN 13
- Thread size: M10 × 1.5
- Thread tolerance: ISO2 (6H)
- Thread direction: Right-hand thread
- Flute form: N (straight flutes)
- Thread pitch: 1.5 mm
Chamfer of the three cutting stages
| No. 1 – taper tap | 6–8-thread chamfer |
|---|---|
| No. 2 – second tap | 4–5-thread chamfer |
| No. 3 – bottoming tap | 2–3-thread chamfer |
The chamfer is the front cutting section in which the thread profile is built up gradually.
Cutting threads – step by step
-
Secure the workpiece
Clamp the workpiece securely so that it cannot rotate. The hole must be readily accessible so that the tap can be started squarely and guided in line with the hole axis throughout the operation. - Prepare the tapping drill hole
Drill the tapping drill hole for M10 × 1.5 to the recommended diameter of 8.5 mm. You can find a clear overview of selection and calculation in the VÖLKEL article Calculating the tapping drill hole size for taps. -
Deburr and clean the hole
Remove the burr at the hole entrance and clear away loose drilling chips. A clean, lightly chamfered hole makes it easier to start the taper tap squarely and prevents damage to the first thread. -
Tapping with the taper tap
Clamp the taper tap in a suitable tool holder and align it precisely with the hole axis. Apply sufficient cutting lubricant for tapping to the tool and hole. Turn the taper tap into the workpiece with steady pressure. -
Tapping with the second tap
Clear loose chips from the hole if necessary and insert the second tap into the thread already started by the taper tap. Again, use sufficient cutting lubricant suitable for the material to ensure an even load on the cutting edges. Continue guiding the tap without sideways pressure. -
Tapping with the bottoming tap
Finally, insert the bottoming tap and apply sufficient cutting lubricant again. The bottoming tap produces the complete internal thread profile. Work with steady movements and avoid excessive force, particularly when the bottoming tap reaches the bottom of a blind hole. -
Check the thread
Remove chips and residual cutting lubricant from the finished thread. Then check the thread size and ease of engagement using a suitable inspection tool, such as a GO/NO-GO thread plug gauge if compliance with the required tolerance must be demonstrated.
Further guidance is available in the VÖLKEL blog article Cutting clean threads: how to produce internal and external threads .
Scope of delivery
Frequently asked questions (FAQ)
- Is M10 × 1.5 a coarse thread on this item?
Yes. This version corresponds to the metric M10 coarse thread to DIN 13 with a 1.5 mm pitch. An M10 fine thread requires a tool with its different pitch.
- Which tapping drill do I need for M10 × 1.5?
For M10 × 1.5, the recommended tap drill diameter is 8.5 mm. Guidance on preparing the tapping drill hole.
As an approximation: tap drill diameter ≈ nominal diameter − pitch. Here: 10 mm − 1.5 mm = 8.5 mm. The recommended drill diameter of 8.5 mm remains decisive.- What does gradual profile build-up mean for the three-piece M10 set?
The taper tap, second tap and bottoming tap are used in sequence and perform matched cutting stages. This distinguishes the set from versions whose tools each have a complete profile and differ only in chamfer length.
- How do I distinguish the tools in this hand tap set?
One ring identifies the taper tap, two rings the second tap and no ring the bottoming tap. Use them in this order.
- Can I also use the HSS-E set for general workshop work?
Yes. The approved application of HSS-E includes general use as well as difficult-to-machine materials. Assess whether the specific material is suitable based on its classification and condition.
- How do I identify and inspect a M10 × 1.5 internal thread?
First measure the outside diameter of the matching bolt or mating component with a caliper and determine the pitch or threads per inch with a thread pitch gauge. Compare the values, thread profile and standard with the designation M10 × 1.5. For an unknown internal thread, identification using a matching external thread or a thread gauge is safer than forcing in a trial fastener. Inspect the finished internal thread dimensionally with a suitable limit thread plug gauge.
- Is the overall length also the achievable M10 thread depth?
No. Overall length, thread length and chamfer describe different sections of the tool. The possible machining depth must suit the hole geometry; additional space must be provided for blind holes.
- What thread tolerance applies to item 57346?
The specified thread tolerance is ISO2 (6H). ISO2 denotes the tool tolerance class; 6H is the associated internal thread tolerance. If necessary, check compliance with the required thread tolerance using a suitable GO/NO-GO thread plug gauge.
- Which tap wrench fits this hand tap?
The holder must securely grip the 5.5 mm square drive. Compare this value with the specified clamping range of the tap wrench or tool holder. Choosing the right tap wrench.
Technical documentation: Hand taps – technical information (PDF) · VD 23 catalogue (PDF, German/English)
Further technical knowledge: Hand taps in the VÖLKEL tap glossary.
Do you need help with selection or use?
Use the VÖLKEL contact form
.
| Type of thread | metric ISO-thread |
|---|---|
| Standard | DIN 352 |
| Material | HSSE |
| Tolerance | ISO2 (6H) |
| Size | M 10 x 1.5 |
| Overall length (L1) | 70 mm |
| Thread length (L2) | 24 mm |
| Core hole diameter (D1) | 8.5 mm |
| Shank diameter (D2) | 7.0 mm |
| Drive connector | 5.5 mm |
| EAN | 4022835573463 |
| Item number | 57346 |
| Type of flute | straight fluted |
| Application | for through and blind holes |
| Thread standard | DIN 13 |